.TH IP6TABLES 8 "Mar 09, 2002" "" ""
.\"
.\" Man page written by Andras Kis-Szabo 
.\" It is based on iptables man page.
.\"
.\" iptables page by Herve Eychenne 
.\" It is based on ipchains man page.
.\"
.\" ipchains page by Paul ``Rusty'' Russell March 1997
.\" Based on the original ipfwadm man page by Jos Vos 
.\"
.\"	This program is free software; you can redistribute it and/or modify
.\"	it under the terms of the GNU General Public License as published by
.\"	the Free Software Foundation; either version 2 of the License, or
.\"	(at your option) any later version.
.\"
.\"	This program is distributed in the hope that it will be useful,
.\"	but WITHOUT ANY WARRANTY; without even the implied warranty of
.\"	MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
.\"	GNU General Public License for more details.
.\"
.\"	You should have received a copy of the GNU General Public License
.\"	along with this program; if not, write to the Free Software
.\"	Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
.\"
.\"
.SH NAME
ip6tables \- IPv6 packet filter administration
.SH SYNOPSIS
.BR "ip6tables [-t table] -[AD] " "chain rule-specification [options]"
.br
.BR "ip6tables [-t table] -I " "chain [rulenum] rule-specification [options]"
.br
.BR "ip6tables [-t table] -R " "chain rulenum rule-specification [options]"
.br
.BR "ip6tables [-t table] -D " "chain rulenum [options]"
.br
.BR "ip6tables [-t table] -[LFZ] " "[chain] [options]"
.br
.BR "ip6tables [-t table] -N " "chain"
.br
.BR "ip6tables [-t table] -X " "[chain]"
.br
.BR "ip6tables [-t table] -P " "chain target [options]"
.br
.BR "ip6tables [-t table] -E " "old-chain-name new-chain-name"
.SH DESCRIPTION
.B Ip6tables
is used to set up, maintain, and inspect the tables of IPv6 packet
filter rules in the Linux kernel.  Several different tables
may be defined.  Each table contains a number of built-in
chains and may also contain user-defined chains.

Each chain is a list of rules which can match a set of packets.  Each
rule specifies what to do with a packet that matches.  This is called
a `target', which may be a jump to a user-defined chain in the same
table.

.SH TARGETS
A firewall rule specifies criteria for a packet, and a target.  If the
packet does not match, the next rule in the chain is the examined; if
it does match, then the next rule is specified by the value of the
target, which can be the name of a user-defined chain or one of the
special values 
.IR ACCEPT ,
.IR DROP ,
.IR QUEUE ,
or
.IR RETURN .
.PP
.I ACCEPT 
means to let the packet through.
.I DROP
means to drop the packet on the floor.
.I QUEUE
means to pass the packet to userspace (if supported by the kernel).
.I RETURN
means stop traversing this chain and resume at the next rule in the
previous (calling) chain.  If the end of a built-in chain is reached
or a rule in a built-in chain with target
.I RETURN
is matched, the target specified by the chain policy determines the
fate of the packet.
.SH TABLES
There are currently two independent tables (which tables are present
at any time depends on the kernel configuration options and which
modules are present), as nat table has not been implemented yet.
.TP
.BI "-t, --table " "table"
This option specifies the packet matching table which the command
should operate on.  If the kernel is configured with automatic module
loading, an attempt will be made to load the appropriate module for
that table if it is not already there.

The tables are as follows:
.RS
.TP .4i
.BR "filter" :
This is the default table (if no -t option is passed).  It contains
the built-in chains
.B INPUT
(for packets coming into the box itself),
.B FORWARD
(for packets being routed through the box), and
.B OUTPUT
(for locally-generated packets).
.TP
.BR "mangle" :
This table is used for specialized packet alteration.  Until kernel
2.4.17 it had two built-in chains:
.B PREROUTING
(for altering incoming packets before routing) and
.B OUTPUT
(for altering locally-generated packets before routing).
Since kernel 2.4.18, three other built-in chains are also supported:
.B INPUT
(for packets coming into the box itself),
.B FORWARD
(for altering packets being routed through the box), and
.B POSTROUTING
(for altering packets as they are about to go out).
.RE
.SH OPTIONS
The options that are recognized by
.B ip6tables
can be divided into several different groups.
.SS COMMANDS
These options specify the specific action to perform.  Only one of them
can be specified on the command line unless otherwise specified
below.  For all the long versions of the command and option names, you
need to use only enough letters to ensure that
.B ip6tables
can differentiate it from all other options.
.TP
.BI "-A, --append " "chain rule-specification"
Append one or more rules to the end of the selected chain.
When the source and/or destination names resolve to more than one
address, a rule will be added for each possible address combination.
.TP
.BI "-D, --delete " "chain rule-specification"
.ns
.TP
.BI "-D, --delete " "chain rulenum"
Delete one or more rules from the selected chain.  There are two
versions of this command: the rule can be specified as a number in the
chain (starting at 1 for the first rule) or a rule to match.
.TP
.B "-I, --insert"
Insert one or more rules in the selected chain as the given rule
number.  So, if the rule number is 1, the rule or rules are inserted
at the head of the chain.  This is also the default if no rule number
is specified.
.TP
.BI "-R, --replace " "chain rulenum rule-specification"
Replace a rule in the selected chain.  If the source and/or
destination names resolve to multiple addresses, the command will
fail.  Rules are numbered starting at 1.
.TP
.BR "-L, --list " "[\fIchain\fP]"
List all rules in the selected chain.  If no chain is selected, all
chains are listed.  As every other iptables command, it applies to the
specified table (filter is the default), so mangle rules get listed by
.nf
 ip6tables -t mangle -n -L
.fi
Please note that it is often used with the
.B -n
option, in order to avoid long reverse DNS lookups.
It is legal to specify the
.B -Z
(zero) option as well, in which case the chain(s) will be atomically
listed and zeroed.  The exact output is affected by the other
arguments given. The exact rules are suppressed until you use
.nf
 ip6tables -L -v
.fi
.TP
.BR "-F, --flush " "[\fIchain\fP]"
Flush the selected chain (all the chains in the table if none is given).
This is equivalent to deleting all the rules one by one.
.TP
.BR "-Z, --zero " "[\fIchain\fP]"
Zero the packet and byte counters in all chains.  It is legal to
specify the
.B "-L, --list"
(list) option as well, to see the counters immediately before they are
cleared. (See above.)
.TP
.BI "-N, --new-chain " "chain"
Create a new user-defined chain by the given name.  There must be no
target of that name already.
.TP
.BR "-X, --delete-chain " "[\fIchain\fP]"
Delete the optional user-defined chain specified.  There must be no references
to the chain.  If there are, you must delete or replace the referring
rules before the chain can be deleted.  If no argument is given, it
will attempt to delete every non-builtin chain in the table.
.TP
.BI "-P, --policy " "chain target"
Set the policy for the chain to the given target.  See the section
.B TARGETS
for the legal targets.  Only built-in (non-user-defined) chains can have
policies, and neither built-in nor user-defined chains can be policy
targets.
.TP
.BI "-E, --rename-chain " "old-chain new-chain"
Rename the user specified chain to the user supplied name.  This is
cosmetic, and has no effect on the structure of the table.
.TP
.B -h
Help.
Give a (currently very brief) description of the command syntax.
.SS PARAMETERS
The following parameters make up a rule specification (as used in the
add, delete, insert, replace and append commands).
.TP
.BR "-p, --protocol " "[!] \fIprotocol\fP"
The protocol of the rule or of the packet to check.
The specified protocol can be one of
.IR tcp ,
.IR udp ,
.IR ipv6-icmp|icmpv6 ,
or
.IR all ,
or it can be a numeric value, representing one of these protocols or a
different one.  A protocol name from /etc/protocols is also allowed.
A "!" argument before the protocol inverts the
test.  The number zero is equivalent to
.IR all .
Protocol
.I all
will match with all protocols and is taken as default when this
option is omitted.
.TP
.BR "-s, --source " "[!] \fIaddress\fP[/\fImask\fP]"
Source specification.
.I Address
can be either a hostname (please note that specifying
any name to be resolved with a remote query such as DNS is a really bad idea),
a network IPv6 address (with /mask), or a plain IPv6 address.
(the network name isn't supported now).
The
.I mask
can be either a network mask or a plain number,
specifying the number of 1's at the left side of the network mask.
Thus, a mask of
.I 64
is equivalent to
.IR ffff:ffff:ffff:ffff:0000:0000:0000:0000 .
A "!" argument before the address specification inverts the sense of
the address. The flag
.B --src
is an alias for this option.
.TP
.BR "-d, --destination " "[!] \fIaddress\fP[/\fImask\fP]"
Destination specification. 
See the description of the
.B -s
(source) flag for a detailed description of the syntax.  The flag
.B --dst
is an alias for this option.
.TP
.BI "-j, --jump " "target"
This specifies the target of the rule; i.e., what to do if the packet
matches it.  The target can be a user-defined chain (other than the
one this rule is in), one of the special builtin targets which decide
the fate of the packet immediately, or an extension (see
.B EXTENSIONS
below).  If this
option is omitted in a rule, then matching the rule will have no
effect on the packet's fate, but the counters on the rule will be
incremented.
.TP
.BR "-i, --in-interface " "[!] \fIname\fP"
Name of an interface via which a packet is going to be received (only for
packets entering the 
.BR INPUT ,
.B FORWARD
and
.B PREROUTING
chains).  When the "!" argument is used before the interface name, the
sense is inverted.  If the interface name ends in a "+", then any
interface which begins with this name will match.  If this option is
omitted, any interface name will match.
.TP
.BR "-o, --out-interface " "[!] \fIname\fP"
Name of an interface via which a packet is going to be sent (for packets
entering the
.BR FORWARD 
and
.B OUTPUT
chains).  When the "!" argument is used before the interface name, the
sense is inverted.  If the interface name ends in a "+", then any
interface which begins with this name will match.  If this option is
omitted, any interface name will match.
.TP
.\" Currently not supported (header-based)
.\" 
.\" .B "[!] " "-f, --fragment"
.\" This means that the rule only refers to second and further fragments
.\" of fragmented packets.  Since there is no way to tell the source or
.\" destination ports of such a packet (or ICMP type), such a packet will
.\" not match any rules which specify them.  When the "!" argument
.\" precedes the "-f" flag, the rule will only match head fragments, or
.\" unfragmented packets.
.\" .TP
.B "-c, --set-counters " "PKTS BYTES"
This enables the administrator to initialize the packet and byte
counters of a rule (during
.B INSERT,
.B APPEND,
.B REPLACE
operations).
.SS "OTHER OPTIONS"
The following additional options can be specified:
.TP
.B "-v, --verbose"
Verbose output.  This option makes the list command show the interface
name, the rule options (if any), and the TOS masks.  The packet and
byte counters are also listed, with the suffix 'K', 'M' or 'G' for
1000, 1,000,000 and 1,000,000,000 multipliers respectively (but see
the
.B -x
flag to change this).
For appending, insertion, deletion and replacement, this causes
detailed information on the rule or rules to be printed.
.TP
.B "-n, --numeric"
Numeric output.
IP addresses and port numbers will be printed in numeric format.
By default, the program will try to display them as host names,
network names, or services (whenever applicable).
.TP
.B "-x, --exact"
Expand numbers.
Display the exact value of the packet and byte counters,
instead of only the rounded number in K's (multiples of 1000)
M's (multiples of 1000K) or G's (multiples of 1000M).  This option is
only relevant for the 
.B -L
command.
.TP
.B "--line-numbers"
When listing rules, add line numbers to the beginning of each rule,
corresponding to that rule's position in the chain.
.TP
.B "--modprobe=command"
When adding or inserting rules into a chain, use
.B command
to load any necessary modules (targets, match extensions, etc).
.SH MATCH EXTENSIONS
ip6tables can use extended packet matching modules.  These are loaded
in two ways: implicitly, when
.B -p
or
.B --protocol
is specified, or with the
.B -m
or
.B --match
options, followed by the matching module name; after these, various
extra command line options become available, depending on the specific
module.  You can specify multiple extended match modules in one line,
and you can use the
.B -h
or
.B --help
options after the module has been specified to receive help specific
to that module.

The following are included in the base package, and most of these can
be preceded by a
.B !
to invert the sense of the match.
.\" @MATCH@
.SS ah
This module matches the SPIs in AH header of IPSec packets.
.TP
.BR "--ahspi " "[!] \fIspi\fP[:\fIspi\fP]"
.SS condition
This matches if a specific /proc filename is '0' or '1'.
.TP
.BI "--condition " "[!] filename"
Match on boolean value stored in /proc/net/ip6t_condition/filename file
.SS dst
This module matches the IPv6 destination header options
.TP
.BI "--dst-len" "[!]" "length"
Total length of this header
.TP
.BI "--dst-opts " "TYPE[:LEN],[,TYPE[:LEN]...]"
Options and it's length (List).
.SS esp
This module matches the SPIs in ESP header of IPSec packets.
.TP
.BR "--espspi " "[!] \fIspi\fP[:\fIspi\fP]"
.SS eui64
This module matches the EUI64 part of a stateless autoconfigured IPv6 address.  It compares the source MAC address with the lower 64 bits of the IPv6 address. 
.SS frag
This module matches the time IPv6 fragmentathion header
.TP
.BI "--fragid " "[!]" "id[:id]"
Matches the given fragmentation ID (range).
.TP
.BI "--fraglen " "[!]" "length"
Matches the total length of this header.
.TP
.BI "--fragres "
Matches the reserved field, too.
.TP
.BI "--fragfirst "
Matches on the first fragment.
.TP
.BI "[--fragmore]"
Matches if there are more fragments.
.TP
.BI "[--fraglast]"
Matches if this is the last fragement.
.SS fuzzy
This module matches a rate limit based on a fuzzy logic controller [FLC]
.TP
.BI "--lower-limit  "number"
Specifies the lower limit (in packets per second).
.TP
.BI "--upper-limit " "number"
Specifies the upper limit (in packets per second).
.SS hbh
This module matches the IPv6 hop-by-hop header options
.TP
.BI "--hbh-len" "[!]" "length"
Total length of this header
.TP
.BI "--hbh-opts " "TYPE[:LEN],[,TYPE[:LEN]...]"
Options and it's length (List).
.SS hl
This module matches the HOPLIMIT field in the IPv6 header.
.TP
.BI "--hl-eq " "value"
Matches if HOPLIMIT equals the given value.
.TP
.BI "--hl-lt " "ttl"
Matches if HOPLIMIT is less than the given value.
.TP
.BI "--hl-gt " "ttl"
Matches if HOPLIMIT is greater than the given value.
.SS icmpv6
This extension is loaded if `--protocol ipv6-icmp' or `--protocol icmpv6' is
specified. It provides the following option:
.TP
.BR "--icmpv6-type " "[!] \fItypename\fP"
This allows specification of the ICMP type, which can be a numeric
IPv6-ICMP type, or one of the IPv6-ICMP type names shown by the command
.nf
 ip6tables -p ipv6-icmp -h
.fi
.SS ipv6header
This module matches on IPv6 option headers
.TP
.BI "--header " "[!]" "headers"
Matches the given type of headers.  
Names: hop,dst,route,frag,auth,esp,none,proto
Long Names: hop-by-hop,ipv6-opts,ipv6-route,ipv6-frag,ah,esp,ipv6-nonxt,protocol
Numbers: 0,60,43,44,51,50,59
.TP
.BI "--soft"
The header CONTAINS the specified extensions.
.SS length
This module matches the length of a packet against a specific value
or range of values.
.TP
.BR "--length " "\fIlength\fP[:\fIlength\fP]"
.SS limit
This module matches at a limited rate using a token bucket filter.
A rule using this extension will match until this limit is reached
(unless the `!' flag is used).  It can be used in combination with the
.B LOG
target to give limited logging, for example.
.TP
.BI "--limit " "rate"
Maximum average matching rate: specified as a number, with an optional
`/second', `/minute', `/hour', or `/day' suffix; the default is
3/hour.
.TP
.BI "--limit-burst " "number"
Maximum initial number of packets to match: this number gets
recharged by one every time the limit specified above is not reached,
up to this number; the default is 5.
.SS mac
.TP
.BR "--mac-source " "[!] \fIaddress\fP"
Match source MAC address.  It must be of the form XX:XX:XX:XX:XX:XX.
Note that this only makes sense for packets coming from an Ethernet device
and entering the
.BR PREROUTING ,
.B FORWARD
or
.B INPUT
chains.
.SS mark
This module matches the netfilter mark field associated with a packet
(which can be set using the
.B MARK
target below).
.TP
.BR "--mark " "\fIvalue\fP[/\fImask\fP]"
Matches packets with the given unsigned mark value (if a mask is
specified, this is logically ANDed with the mask before the
comparison).
.SS multiport
This module matches a set of source or destination ports.  Up to 15
ports can be specified.  It can only be used in conjunction with
.B "-p tcp"
or
.BR "-p udp" .
.TP
.BR "--source-ports " "\fIport\fP[,\fIport\fP[,\fIport\fP...]]"
Match if the source port is one of the given ports.  The flag
.B --sports
is a convenient alias for this option.
.TP
.BR "--destination-ports " "\fIport\fP[,\fIport\fP[,\fIport\fP...]]"
Match if the destination port is one of the given ports.  The flag
.B --dports
is a convenient alias for this option.
.TP
.BR "--ports " "\fIport\fP[,\fIport\fP[,\fIport\fP...]]"
Match if the both the source and destination ports are equal to each
other and to one of the given ports.
.SS nth
This module matches every `n'th packet
.TP
.BI "--every " "value"
Match every `value' packet
.TP
.BI "[" "--counter " "num" "]"
Use internal counter number `num'.  Default is `0'.
.TP
.BI "[" "--start " "num" "]"
Initialize the counter at the number `num' insetad of `0'.  Most between `0'
and `value'-1.
.TP
.BI "[" "--packet " "num" "]"
Match on `num' packet.  Most be between `0' and `value'-1.
.SS owner
This module attempts to match various characteristics of the packet
creator, for locally-generated packets.  It is only valid in the
.B OUTPUT
chain, and even this some packets (such as ICMP ping responses) may
have no owner, and hence never match.  This is regarded as experimental.
.TP
.BI "--uid-owner " "userid"
Matches if the packet was created by a process with the given
effective user id.
.TP
.BI "--gid-owner " "groupid"
Matches if the packet was created by a process with the given
effective group id.
.TP
.BI "--pid-owner " "processid"
Matches if the packet was created by a process with the given
process id.
.TP
.BI "--sid-owner " "sessionid"
Matches if the packet was created by a process in the given session
group.
.TP
.B NOTE: pid, sid and command matching are broken on SMP
.SS physdev
This module matches on the bridge port input and output devices enslaved
to a bridge device. This module is a part of the infrastructure that enables
a transparent bridging IP firewall and is only useful for kernel versions
above version 2.5.44.
.TP
.B --physdev-in name
Name of a bridge port via which a packet is received (only for
packets entering the
.BR INPUT ,
.B FORWARD
and
.B PREROUTING
chains). If the interface name ends in a "+", then any
interface which begins with this name will match. If the packet didn't arrive
through a bridge device, this packet won't match this option, unless '!' is used.
.TP
.B --physdev-out name
Name of a bridge port via which a packet is going to be sent (for packets
entering the
.BR FORWARD ,
.B OUTPUT
and
.B POSTROUTING
chains).  If the interface name ends in a "+", then any
interface which begins with this name will match. Note that in the
.BR nat " and " mangle
.B OUTPUT
chains one cannot match on the bridge output port, however one can in the
.B "filter OUTPUT"
chain. If the packet won't leave by a bridge device or it is yet unknown what
the output device will be, then the packet won't match this option, unless
'!' is used.
.TP
.B --physdev-is-in
Matches if the packet has entered through a bridge interface.
.TP
.B --physdev-is-out
Matches if the packet will leave through a bridge interface.
.TP
.B --physdev-is-bridged
Matches if the packet is being bridged and therefore is not being routed.
This is only useful in the FORWARD and POSTROUTING chains.
.SS random
This module randomly matches a certain percentage of all packets.
.TP
.BI "--average " "percent"
Matches the given percentage.  If omitted, a probability of 50% is set. 
.SS rt
Match on IPv6 routing header
.TP
.BI "--rt-type " "[!]" "type"
Match the type (numeric).
.TP
.BI "--rt-segsleft" "[!]" "num[:num]"
Match the `segments left' field (range).
.TP
.BI "--rt-len" "[!]" "length"
Match the length of this header
.TP
.BI "--rt-0-res"
Match the reserved field, too (type=0)
.TP
.BI "--rt-0-addrs ADDR[,ADDR...]
Match type=0 addresses (list).
.TP
.BI "--rt-0-not-strict"
List of type=0 addresses is not a strict list.
.SS tcp
These extensions are loaded if `--protocol tcp' is specified. It
provides the following options:
.TP
.BR "--source-port " "[!] \fIport\fP[:\fIport\fP]"
Source port or port range specification. This can either be a service
name or a port number. An inclusive range can also be specified,
using the format
.IR port : port .
If the first port is omitted, "0" is assumed; if the last is omitted,
"65535" is assumed.
If the second port greater then the first they will be swapped.
The flag
.B --sport
is a convenient alias for this option.
.TP
.BR "--destination-port " "[!] \fIport\fP[:\fIport\fP]"
Destination port or port range specification.  The flag
.B --dport
is a convenient alias for this option.
.TP
.BR "--tcp-flags " "[!] \fImask\fP \fIcomp\fP"
Match when the TCP flags are as specified.  The first argument is the
flags which we should examine, written as a comma-separated list, and
the second argument is a comma-separated list of flags which must be
set.  Flags are: 
.BR "SYN ACK FIN RST URG PSH ALL NONE" .
Hence the command
.nf
 ip6tables -A FORWARD -p tcp --tcp-flags SYN,ACK,FIN,RST SYN
.fi
will only match packets with the SYN flag set, and the ACK, FIN and
RST flags unset.
.TP
.B "[!] --syn"
Only match TCP packets with the SYN bit set and the ACK and RST bits
cleared.  Such packets are used to request TCP connection initiation;
for example, blocking such packets coming in an interface will prevent
incoming TCP connections, but outgoing TCP connections will be
unaffected.
It is equivalent to \fB--tcp-flags SYN,RST,ACK SYN\fP.
If the "!" flag precedes the "--syn", the sense of the
option is inverted.
.TP
.BR "--tcp-option " "[!] \fInumber\fP"
Match if TCP option set.
.SS udp
These extensions are loaded if `--protocol udp' is specified.  It
provides the following options:
.TP
.BR "--source-port " "[!] \fIport\fP[:\fIport\fP]"
Source port or port range specification.
See the description of the
.B --source-port
option of the TCP extension for details.
.TP
.BR "--destination-port " "[!] \fIport\fP[:\fIport\fP]"
Destination port or port range specification.
See the description of the
.B --destination-port
option of the TCP extension for details.
.SH TARGET EXTENSIONS
ip6tables can use extended target modules: the following are included
in the standard distribution.
.\" @TARGET@
.SS HL
This is used to modify the IPv6 HOPLIMIT header field.  The HOPLIMIT field is 
similar to what is known as TTL value in IPv4.  Setting or incrementing the
HOPLIMIT field can potentially be very dangerous, so it should be avoided at
any cost.  
.TP
.B Don't ever set or increment the value on packets that leave your local network!
.B mangle
table.
.TP
.BI "--hl-set " "value"
Set the HOPLIMIT value to `value'.
.TP
.BI "--hl-dec " "value"
Decrement the HOPLIMIT value `value' times.
.TP
.BI "--hl-inc " "value"
Increment the HOPLIMIT value `value' times.
.SS LOG
Turn on kernel logging of matching packets.  When this option is set
for a rule, the Linux kernel will print some information on all
matching packets (like most IPv6 IPv6-header fields) via the kernel log
(where it can be read with
.I dmesg
or 
.IR syslogd (8)).
This is a "non-terminating target", i.e. rule traversal continues at
the next rule.  So if you want to LOG the packets you refuse, use two
separate rules with the same matching criteria, first using target LOG
then DROP (or REJECT).
.TP
.BI "--log-level " "level"
Level of logging (numeric or see \fIsyslog.conf\fP(5)).
.TP
.BI "--log-prefix " "prefix"
Prefix log messages with the specified prefix; up to 29 letters long,
and useful for distinguishing messages in the logs.
.TP
.B --log-tcp-sequence
Log TCP sequence numbers. This is a security risk if the log is
readable by users.
.TP
.B --log-tcp-options
Log options from the TCP packet header.
.TP
.B --log-ip-options
Log options from the IPv6 packet header.
.SS MARK
This is used to set the netfilter mark value associated with the
packet.  It is only valid in the
.B mangle
table.
.TP
.BI "--set-mark " "mark"
.SS REJECT
This is used to send back an error packet in response to the matched
packet: otherwise it is equivalent to 
.B DROP
so it is a terminating TARGET, ending rule traversal.
This target is only valid in the
.BR INPUT ,
.B FORWARD
and
.B OUTPUT
chains, and user-defined chains which are only called from those
chains.  The following option controls the nature of the error packet
returned:
.TP
.BI "--reject-with " "type"
The type given can be
.nf
.B " icmp6-no-route"
.B " no-route"
.B " icmp6-adm-prohibited"
.B " adm-prohibited"
.B " icmp6-addr-unreachable"
.B " addr-unreach"
.B " icmp6-port-unreachable"
.B " port-unreach"
.fi
which return the appropriate IPv6-ICMP error message (\fBport-unreach\fP is
the default). Finally, the option
.B tcp-reset
can be used on rules which only match the TCP protocol: this causes a
TCP RST packet to be sent back.  This is mainly useful for blocking 
.I ident
(113/tcp) probes which frequently occur when sending mail to broken mail
hosts (which won't accept your mail otherwise).

.SS ROUTE
This is used to explicitly override the core network stack's routing decision.
.B mangle
table.
.TP
.BI "--oif " "ifname"
Route the packet through `ifname' network interface
.TP
.BI "--gw " "IPv6_address"
Route the packet via this gateway
.TP
.BI "--continue "
Behave like a non-terminating target and continue traversing the rules. Not valid in combination with `--tee'
.TP
.BI "--tee "
Make a copy of the packet, and route that copy to the given destination. For the original, uncopied packet, behave like a non-terminating target and continue traversing the rules.  Not valid in combination with `--continue'
.SS TRACE
This target has no options.  It just turns on 
.B packet tracing
for all packets that match this rule.
.SH DIAGNOSTICS
Various error messages are printed to standard error.  The exit code
is 0 for correct functioning.  Errors which appear to be caused by
invalid or abused command line parameters cause an exit code of 2, and
other errors cause an exit code of 1.
.SH BUGS
Bugs?  What's this? ;-)
Well... the counters are not reliable on sparc64.
.SH COMPATIBILITY WITH IPCHAINS
This 
.B ip6tables
is very similar to ipchains by Rusty Russell.  The main difference is
that the chains 
.B INPUT
and
.B OUTPUT
are only traversed for packets coming into the local host and
originating from the local host respectively.  Hence every packet only
passes through one of the three chains (except loopback traffic, which
involves both INPUT and OUTPUT chains); previously a forwarded packet
would pass through all three.
.PP
The other main difference is that 
.B -i
refers to the input interface;
.B -o
refers to the output interface, and both are available for packets
entering the
.B FORWARD
chain.
.\" .PP The various forms of NAT have been separated out; 
.\" .B iptables 
.\" is a pure packet filter when using the default `filter' table, with
.\" optional extension modules.  This should simplify much of the previous
.\" confusion over the combination of IP masquerading and packet filtering
.\" seen previously.  So the following options are handled differently:
.\" .br
.\" -j MASQ
.\" .br
.\" -M -S
.\" .br
.\" -M -L
.\" .br
There are several other changes in ip6tables.
.SH SEE ALSO
.BR ip6tables-save (8),
.BR ip6tables-restore(8),
.BR iptables (8),
.BR iptables-save (8),
.BR iptables-restore (8).
.P
The packet-filtering-HOWTO details iptables usage for
packet filtering, the NAT-HOWTO details NAT,
the netfilter-extensions-HOWTO details the extensions that are
not in the standard distribution,
and the netfilter-hacking-HOWTO details the netfilter internals.
.br
See
.BR "http://www.netfilter.org/" .
.SH AUTHORS
Rusty Russell wrote iptables, in early consultation with Michael
Neuling.
.PP
Marc Boucher made Rusty abandon ipnatctl by lobbying for a generic packet
selection framework in iptables, then wrote the mangle table, the owner match,
the mark stuff, and ran around doing cool stuff everywhere.
.PP
James Morris wrote the TOS target, and tos match.
.PP
Jozsef Kadlecsik wrote the REJECT target.
.PP
Harald Welte wrote the ULOG target, TTL match+target and libipulog.
.PP
The Netfilter Core Team is: Marc Boucher, Martin Josefsson, Jozsef Kadlecsik,
James Morris, Harald Welte and Rusty Russell.
.PP
ip6tables man page created by Andras Kis-Szabo, based on
iptables man page written by Herve Eychenne .
.\" .. and did I mention that we are incredibly cool people?
.\" .. sexy, too ..
.\" .. witty, charming, powerful ..
.\" .. and most of all, modest ..

Web www.fiveanddime.net